SCCBC Forum - Time attack safety questions

	Welcome, Guest. Please Login or Register

Home

Help

SCCBC Forum › General › Tech Corner › Time attack safety questions

(Moderator: Forum Admin)

‹ Previous Topic | Next Topic ›

Pages: 1

Time attack safety questions (Read 3,148 times)

Jeremy

Spectator

Offline

SCCBC Forum Member

Posts: 8

Time attack safety questions
Feb 13^th, 2018 at 6:09pm

Hello everyone,

I'm preparing a cheap car I got for lapping days and time attack for the upcoming season. I plan to try and do most the time attack no pass events this season to try and keep cost down.

I have run into part of the GCR that has me stumped. I have a Kirkie roadrace seat for the car. I was looking up requirements for mounting and such and found a hurdle. Everything in the rule book is in reference to cars with cages. In there it says the back needs to be tied into the cage.......I don't have one or need on for no pass.

I was planing on mounting the seat and then using a factory 3 point (like lapping days). I don't know if I feel comfortable installing a 6 point harness into a car with a fixed back seat and no harness bar to tie the shoulder belts into. If I do install them the shoulder belts will be at an angle that would think would seriously compress my back in an accident.

I guess my question is what can I do for time attack no pass to get a seat that supports me in corners and will pass tech.

Thanks,

Hope to meet a few of you out there.

IP Logged

Mike_the_Oldest International License Offline Posts: 884 B.C.	Re: Time attack safety questions Reply #1 - Feb 14^th, 2018 at 1:07pm You should contact Campbell Carlyle (tad@caccautosport.org) who is the director in charge of this. He will be able to advise you. Thanks for asking. Mike Currie
Back to top	IP Logged

Jeremy Spectator Offline SCCBC Forum Member Posts: 8	Re: Time attack safety questions Reply #2 - Feb 14^th, 2018 at 3:49pm Mike_the_Oldest wrote on Feb 14^th, 2018 at 1:07pm: You should contact Campbell Carlyle (tad@caccautosport.org) who is the director in charge of this. He will be able to advise you. Thanks for asking. Mike Currie Thanks Mike.
Back to top	IP Logged

ip2gsr

Novice

Offline

Road racing, not street
racing!

Posts: 86

Re: Time attack safety questions
Reply #3 - Feb 19^th, 2018 at 5:48pm

Jeremy wrote on Feb 13^th, 2018 at 6:09pm:

H

I was planing on mounting the seat and then using a factory 3 point (like lapping days). I don't know if I feel comfortable installing a 6 point harness into a car with a fixed back seat and no harness bar to tie the shoulder belts into. If I do install them the shoulder belts will be at an angle that would think would seriously compress my back in an accident.

I guess my question is what can I do for time attack no pass to get a seat that supports me in corners and will pass tech.

Thanks,

Hope to meet a few of you out there.

First off.... thanks for reading the rules.....

I'm a road racer and not a tech official but if you don't have a cage you would not require a rear seat back brace. This assumes that the rules allow an alternate seat in the first place.

A seat belt has to be tight across your hips to work properly. The Kirkey seats normally have a small triangular shaped opening that close to the base of the seat. If you use a stock belt it should not be over the top of the seat side support. Can you get both the latch and the belt through the hole on the left and right side of the seat so that it can be worn properly? I would guess not but that would be my concern.

Certainly the time attack tech folks would be more informed and as Mike mentions Campbell would be the right path to get in touch with them.

Dave

IP Logged

Pages: 1

‹ Previous Topic | Next Topic ›

« Home

‹ Board

Top of this page